Neogel 8300-W-9737 gelcoat belongs to the AOC Neogel 8300-W series of isophthalic mould gelcoats for glass-reinforced plastic (GRP) tooling. The manufacturer describes the series as pre-accelerated and thixotropic, with a high-gloss finish and good hardness. The supplied PDS covers the series. Confirm the brush or spray version and the specification applicable to the 9737 code when requesting a quote.
Neogel 8300-W-9737 Gelcoat: Brush and Spray Data
Use the 8300-W reference values below to compare application variants when evaluating Neogel 8300-W-9737 gelcoat. Each column describes a different base formulation in the manufacturer’s series PDS. Confirm which column applies to the offered product before setting inspection or production limits.
| Base gelcoat property | Test method | Brush grade | Spray grade |
|---|---|---|---|
| Appearance | TM 2265 | Thixotropic liquid | Thixotropic liquid |
| Viscosity at 25 °C, spindle #4, 2 rpm | TM 5042 | 26,000–45,000 mPa·s | 22,000–40,000 mPa·s |
| Viscosity at 25 °C, spindle #4, 20 rpm | TM 5042 | 6,500–10,000 mPa·s | 3,500–5,000 mPa·s |
| Gel time at 25 °C | TM 2245 | 10–20 min | 10–20 min |
The viscosity ranges depend on spindle speed. If incoming inspection uses a different spindle, speed or temperature, agree on a comparable method before interpreting the result. The published gel time is a laboratory value. Assess application time on a representative trial using the intended equipment, mould surface and workshop conditions.
Cured Properties for Neogel 8300-W-9737 Gelcoat Selection
| Cured base gelcoat property | Typical series value | Test method |
|---|---|---|
| Tensile strength | 90 MPa | ISO 527-2 |
| Tensile modulus | 3,700 MPa | ISO 527-2 |
| Elongation at break | 4.6% | ISO 527-2 |
| Heat deflection temperature | 95 °C | ISO 75A |
The series PDS reports these values after curing the test material for 24 hours at room temperature, followed by 24 hours at 80 °C. For a reusable mould, assess the gelcoat and backing laminate together under the intended production and demoulding cycles. Treat the published heat deflection temperature as a test result for the cured base material.
Four Checks Before Specifying Neogel 8300-W-9737 Gelcoat
1. Confirm the application method. Specify whether the operator will brush, roll or spray. For spray application, share the type of equipment and request the applicable technical instructions.
2. Agree on the finish. Send the approved colour reference, gloss expectations and inspection criteria. Compare an approved sample under the same lighting and on a representative surface before placing a production order.
3. Qualify the tooling system. Identify the backing laminate, tool geometry and expected service cycle. Use a trial panel to assess the surface finish and the behaviour of the full system before committing to a larger mould.
4. Confirm the pack and lot details. The series PDS gives a reference pack size of about 21 kg. Ask the supplier to confirm the offered net weight and available quantity for the exact 9737 version. Confirm any lot documentation required for receiving inspection.
Neogel 8300-W-9737 Supplier and TDS Requests
When contacting a Neogel 8300-W-9737 supplier, use the full AOC Neogel 8300-W-9737 designation and include your tooling application, application method, colour reference, order quantity and delivery destination. For repeat orders, include the prior purchase or lot reference so the supplier can match the version.
Request the current Neogel 8300-W-9737 TDS and SDS before a trial. The series PDS lists three months of typical stability from dispatch in the original unopened package at no more than 20 °C, protected from sunlight and heat. Confirm the remaining shelf life of the offered lot and follow the current SDS and label for storage and handling.
Browse the AOC resin and Neogel gelcoat range for related products. The AOC product brand overview provides manufacturer context for the range.