LOCTITE® FREKOTE® 770-NC is a clear, solvent-based, moisture-cured, epoxy mold release agent for advanced composites and FRP polyester parts. It is a versatile, semi-permanent release agent with high thermal stability, with high slip to compensate for mold geometry problems. Wiped or sprayed on, it creates a high gloss finish, and dry time between coats is just 5-10 min.
Products Brand | |
---|---|
Additive Classification | Mold Release Agents |
Industry | Automotive & Transportation, Building & Construction, Electrical & Electronics, Marine Vessels |
Technology | Mold Release |
Appearance | Clear, colorless |
Chemical Type | Solvent Based Polymer |
Odor | Solvent |
Cure | Room temperature cure |
Cured Thermal Stability | ≤400 °C |
Application | Release Coatings |
Application Temperature | 15 to 60 °C |
Specific Benefits | ● No contaminating transfer ● High gloss finish ● High slip ● No mold build-up ● Low odor |
1. LOCTITE® FREKOTE 770-NC™ can be applied to mold surfaces at room temperature up to 60°C by spraying, brushing or wiping with a clean lint-free, cloth. When spraying ensure a dry air source is used or use an airless spray system. Always use in a well ventilated area.
2. Wipe or spray on a smooth, thin, continuous, wet film. Avoid wiping or spraying over the same area that was just coated until the solvent has evaporated. If spraying, hold nozzle 20 to 30cm from mold surface. It is suggested that small areas be coated, working progressively from one side of the mold to the other.
3. Initially, apply 2 to 3 base coats allowing 5 to 10 minutes between coats for solvent evaporation .
4. Allow the final coat to cure for 5 to 10 minutes at 22°C.
5. Maximum releases will be obtained as the mold surface becomes conditioned to LOCTITE® FREKOTE 770-NC™ . Performance can be enhanced by re-coating once, after the first few initial pulls.
6. When any release difficulty is experienced, the area in question can be “touched-up” by re-coating the entire mold surface or just those areas where release difficulty is occurring.
7. NOTE: LOCTITE® FREKOTE 770-NC™ is moisture sensitive, keep container tightly closed when not in use. The product should always be used in a well ventilated area.
8. Precaution: Users of closed mold systems (rotomolding) must be certain that solvent evaporation is complete and that all solvent vapors have been ventilated from the mold cavity prior to closing the mold. An oil-free compressed air source can be used to assist in evaporation of solvents and ventilation of the mold cavity.
Brand:Perkadox®
Chemical family:Organic peroxide
CAS number:80-43-3
Physical form:Crystal
Molecular Weight:270.4
Concentration:5.86% min.
Chemical name:Dicumyl peroxide
Brand:Trigonox®
Chemical family:Organic peroxide
CAS number:37206-20-5
Physical form:Liquid
Chemical name:Methyl isobutyl ketone peroxide
Brand:Trigonox
Chemical family:Organic peroxide
CAS number:927-07-1
Physical form:Liquid
Molecular Weight:174.2
Concentration:6.89%
Chemical name:tert-Butyl peroxypivalate, 75% solution in isododecane
Brand:Butanox®
Chemical family:Organic peroxide
CAS number:1338-23-4
Physical form:Liquid
Chemical name:Methyl ethyl ketone peroxide in diisononyl phthalate
Brand:Butanox®
Chemical family:Organic peroxide
CAS number:1338-23-4
Physical form:Liquid
Chemical name:Methyl ethyl ketone peroxide, solution in dimethyl phthalate
Appearance: Brown-yellow transparent liquid
Density: 1.05-1.07kg/L
Viscosity: 1 350±100cps
Solid content: 55±1%
Gelation time: 2 15±5min
Shelf life: 6 months (below 25℃)
Fill out the form below, and we will be in touch shortly.