LOCTITE® FREKOTE® PMC is a post-cleaner with a special blend of solvents designed to dissolve and remove wax from polyester molds without dulling the surface. It can also be used to clean epoxy and metal mold surfaces, as well brushes and equipment. It is highly recommended for preparing polyester mold surfaces prior to the application of LOCTITE® FREKOTE® mold sealers and release agents.
| Supplier | |
|---|---|
| Additive Classification | Mold Release Agents |
| Industry | Automotive & Transportation, Building & Construction, Home Renovation, Marine Vessels, Petrochemical, Wind Energy |
| Specific Gravity @ 23 °C | 1.1 |
| Viscosity, Brookfield – RVT @ 25 °C | Spindle 2, speed 20 rpm |
| mPa·s (cP) | 500 |
| Viscosity, Cone & Plate, 25°C, mPa·s (cP) | Cone C60/1°Ti @ shear rate 129 s-1 |
| mPa·s (cP): | 450 |
For Assembly
1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry.
2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed.
3. Shake the product thoroughly before use.
4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application.
5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area.
6. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole.
7. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free.Force the material into the threads to thoroughly fill the voids.For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also.
8. Assemble and tighten as required.
For Disassembly
1. Apply localized heat to nut or bolt to approximately 250°C.Disassemble while hot.
Clean-up:
1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush.
True high-gloss paste wax.
Withstands high-temperature exothermic reactions of resins and does multiple releases easily.
Contains carnauba wax, synthetic waxes and high-temperature resistant resins for effective multiple releases of plastic parts through numerous cycles.
Brand：Perkadox®
CAS number：94-36-0
Molecular Weight：242.2
Concentration：3.20-3.37%
Chemical name：Dibenzoyl peroxide, paste, 50% in dipropylene glycol dibenzoate and water
Brand:Polylite
Appearance:Light yellow transparent viscous liquid
Acid Value:14-20mgKOH/g
Viscosity，25℃:0.14-0.16Pa.s
Solid Content:52-58%
Gel time:25-38min
Brand:Polylite
Appearance: Clear liquid,no visible mechanical impurity
Epoxy Equivalent (g/eq): 176–184
Color (Gardner): Max 1.0
Flash Point (℃): Above 150
Viscosity (cps, at 25℃): 8000–11000
Hydrolyzable Chlorine Content (ppm): Below 1000
Specific Gravity (g/cm³, 25℃): 1.16
Brand:Polylite
Appearance:Clear liquid,no visible mechanical impurity
Colour(Hazen):40 Max
Epoxy Equivalent(g/mol):210-230
Hydrolytic Chlorine (%):0.50 Max
Inorg.Cl （mg/kg）:50 Max
Volatile /150℃,40min(%):0.6 Max
Softening Point(℃):14-23
Brand:Polylite
Appearance: light yellow transparent liquid
Density: 1.06±0.02kg/L
Viscosity: 430±150 cps (LVT#3-60rpm/25℃)
Solid content: 62±1.5%
Gelation time: 15-25 minutes
