LOCTITE® FREKOTE® PMC is a post-cleaner with a special blend of solvents designed to dissolve and remove wax from polyester molds without dulling the surface. It can also be used to clean epoxy and metal mold surfaces, as well brushes and equipment. It is highly recommended for preparing polyester mold surfaces prior to the application of LOCTITE® FREKOTE® mold sealers and release agents.
| Supplier | |
|---|---|
| Additive Classification | Mold Release Agents |
| Industry | Automotive & Transportation, Building & Construction, Home Renovation, Marine Vessels, Petrochemical, Wind Energy |
| Specific Gravity @ 25 °C | 1.1 |
| Flash point | see SDS |
| Viscosity, Brookfield – RVT, 25°C | Spindle 3, speed 20 rpm, Helipath |
| mPa·s (cP) | 1,200 to 2,400 |
| Viscosity, EN 12092 – MV, 25 °C, after 180 s | Shear rate 129 s-1 |
| mPa·s (cP): | 400 |
For Assembly
1. For best results, clean all surfaces (external and internal)with a LOCTITE®
cleaning solvent and allow to dry.
2. If the material is an inactive metal or the cure speed is too slow, spray all threads with and allow to dry.
3. Shake the product thoroughly before use.
4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application.
5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area.
6. For Blind Holes, apply several drops of the product down the internal threads to the bottom of the hole.
7. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids,adjust product amount accordingly and apply a 360° bead of product on the female thread
For Disassembly
1. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot
Clean-up:
1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush.
Brand:Trigonox
Chemical family:Organic peroxide
CAS number:927-07-1
Physical form:Liquid
Molecular Weight:174.2
Concentration:6.89%
Chemical name:tert-Butyl peroxypivalate, 75% solution in isododecane
Brand：Trigonox
Chemical family：Organic peroxide
CAS number：26748-41-4
Physical form：Liquid
Molecular Weight：244.4
Chemical name：tert-Butyl peroxyneodecanoate, 75% solution in isododecane
Brand:Butanox®
Chemical family:Organic peroxide
CAS number:1338-23-4
Physical form:Liquid
Chemical name:Methyl ethyl ketone peroxide in diisononyl phthalate
Brand:Butanox®
Chemical family:Organic peroxide
CAS number:1338-23-4
Physical form:Liquid
Chemical name:Methyl ethyl ketone peroxide, solution in dimethyl phthalate
Brand:Polylite
Physical State:liquid
Epoxy Equivalent (g/eq):184～190
Color (Gardner):1.0max
Flash Point (℃):150↑
Viscosity (cps, at 25℃)：12000～15000
Hydrolyzable Chlorine Content (ppm)：1000↓
Specific Gravity (g/cm³, 25℃)：1.16
Brand:Polylite
Appearance: Clear liquid,no visible mechanical impurity
Epoxy Equivalent (g/eq): 176–184
Color (Gardner): Max 1.0
Flash Point (℃): Above 150
Viscosity (cps, at 25℃): 8000–11000
Hydrolyzable Chlorine Content (ppm): Below 1000
Specific Gravity (g/cm³, 25℃): 1.16
