LOCTITE® FREKOTE® FMS Mold Release Agents

LOCTITE® FREKOTE FMS™ is formulated specifically as a sealer for fiberglass reinforced polyester, epoxy and other composite molds commonly used in the fiberglass molding industry. LOCTITE® FREKOTE FMS™ must be used when using green, or new, molds with microporosity and other slight surface imperfections.

Additional information

Supplier

Industry

Automotive & Transportation, Building & Construction, Marine Vessels, Petrochemical

Additive Classification

Mold Release Agents

Product Description

Technology Mold Release
Appearance Clear, colorless
Chemical Type Solvent Based Polymer
Odor Hydrocarbon
Cure Room temperature cure
Application Mold Sealer
Application Temperature 13 to 35 °C
Specific Benefit ●High gloss finish
● Easy application
● Fast curing
● Eliminates Porosity/Microporosity
● Seals “green” molds and repaired areas

Directions for Use

1. Apply LOCTITE® Frekote WOLO™ with a clean, lint free, cotton wiping cloth. Wet the cloth with LOCTITE® Frekote WOLO™ until it is damp but not dripping.

2. Wipe a smooth, wet film over the entire mold surface. For larger molds, apply LOCTITE® Frekote WOLO™ to the surface one section at a time starting at one end and working towards the other. Continue to work the material into the mold by lightly wiping the wet film (10-30 seconds) until a thin and uniform coating is obtained, and then allow the product to evaporate.

3. Allow a minimum of 5 minutes before applying next coat. Apply a minimum of four coats in this manner. Dampen cloth lightly as needed.

4. Allow the final coat to cure for 15 minutes at 20°C.

5. NOTE: If the cloth dries out during your coating process, use a fresh clean cloth to apply the next coat. This prevents resin accumulation on the cloth from being deposited on the mold surface. If streaking occurs, replace the cloth with a clean dry one and/or make sure that the cloth is just damp and not soaking wet. Avoid over-application, as this will cause streaking on the tooling surface. Streaks or wipe lines can be removed easily by wiping the mold surface lightly with a dry cloth. Product is moisture sensitive, keep container tightly closed when not in use.

6. NOTE: For maximum number of releases, apply a touch up coat after the first 2-3 parts are released as a break in period after the initial application. On deep or high wear areas, apply an extra 1-2 coats of LOCTITE® Frekote WOLO™. This will help increase the slip even further in these high drag areas.

E01 Emulsion Chopped Strand Mats

High tensile strength, allowing for use in hand lay-up process to produce large-area parts,
no airborne fiber when operating, good wet-through and fast wet-out in resins, rapid air
lease, high mechanical strength, superior acid corrosion resistance

Perkadox GB-50L Dibenzoyl peroxide

Brand:Perkadox®
Chemical family:Organic peroxide
CAS number:94-36-0
Physical form:Granular powder
Chemical name:Dibenzoyl peroxide

Butanox M-50 Organic Peroxide

Brand:Butanox®
Chemical family:Organic peroxide
CAS number:1338-23-4
Physical form:Liquid
Chemical name:Methyl ethyl ketone peroxide, solution in dimethyl phthalate

Butanox M-60 Organic Peroxide

Brand:Butanox®
Chemical family:Organic peroxide
CAS number:1338-23-4
Physical form:Liquid
Chemical name:Methyl ethyl ketone peroxide

ZC-638 Epoxy Resin

Appearance: Semi-solid
Epoxy equivalent (g/eq): 170-190
*Hue(G): 3.0Max.
Flash point (℃): 250↑
Solution viscosity (25℃): H~K
Density (g/cm³ 20℃): 1.18

ZC-907 Vinyl Resin

Appearance: light yellow transparent liquid
Density: 1.06±0.02kg/L
Viscosity: 430±150 cps (LVT#3-60rpm/25℃)
Solid content: 62±1.5%
Gelation time: 15-25 minutes

Get a Quote

Get a Quick Quote

Fill out the form below, and we will be in touch shortly.